Aluminum Bullet Turn Signals (Pair)

Aluminum Bullet Turn Signals for Vintage Honda Motorcycles

Upgrade the lighting on your vintage Honda with these aluminum bullet-style turn signals. Each pair features a single-piece aluminum body available in polished chrome or black, with a 12V dual-filament 1157 bulb that functions as both a turn signal and a running light. Pre-wired with Honda-style bullet connectors for a clean, plug-compatible installation on CB175, CB200, CB350, CB360, CB450, CB500T, CB500K, CB550, and CB750 models (1965–1978).

Why You Need This

Original turn signal assemblies on vintage Hondas are often cracked, faded, or missing entirely. These aluminum bullet signals are a direct stem-mount replacement that fits the factory signal stems with a nut-and-washer clamp—just like the OEM signals. The compact bullet profile sits tighter to the bike than stock housings, giving the front and rear a cleaner look without requiring custom brackets or fabrication. The dual-filament 1157 bulb means you get both turn signal and running light capability in one unit, so bikes with post-1974 running light circuits (CB360, CB550, CB750) are fully covered. For single-circuit bikes (CB175, CB350, CB450, CB500K), you simply cap off the running light wire.

Pair these with a Headlight Bucket & H4 Bulb Kit and a set of Headlight Brackets for a complete front-end lighting refresh.

Specifications

Important Notes

• These signals use a 12V dual-filament 1157 bulb. If you are converting to LED bulbs, you will need an Electronic Flasher Relay to get the correct flash rate—the stock thermal relay depends on incandescent current draw to cycle.
• The stem mount design clamps onto the existing turn signal stem on your bike. These do not include the stems themselves—they use your original mounting stems or aftermarket replacements.
• The included 1157 bulb is a low-profile style. Standard full-size 1157 bulbs will also work but may sit slightly taller in the housing.

Model-Specific Notes

• CB175 / CB350 / CB450 / CB500K (pre-1974): These bikes use a single-circuit turn signal system—no running lights. Wire the black (ground) and black/white stripe (turn signal) leads. Cap off the red (running light) wire with a crimp cap or electrical tape.
• CB360 / CB550 / CB750 (1974 and later): These bikes have a running light circuit per DOT regulations introduced around 1974. Wire all three leads: black (ground), black/white stripe (turn signal), and red (running light). The running lights stay on whenever the key is turned on.
• CB200: The CB200 bridges both eras—the 1973 CB200K0 uses a single-circuit setup, while the 1974+ CB200T has the running light circuit. Check your wiring harness at the headlight bucket for a running light wire to confirm which setup your bike has.
• CL and SL Scramblers: All CL175, CL200, CL350, CL360, CL450, SL175, and SL350 models are compatible. Same wiring rules apply based on year (pre-1974 = single circuit, 1974+ = dual circuit).

Installation

1. Remove the old turn signal from the mounting stem (unscrew the retaining nut).
2. Disconnect the original wiring at the bullet connectors inside the headlight bucket or under the seat (rear signals).
3. Slide the new aluminum bullet signal onto the stem and secure with the included nut and washer.
4. Connect the wiring using the Honda-style bullet connectors:
   • Black → Ground
   • Black w/ White Stripe → Turn signal circuit
   • Red → Running light circuit (cap off on single-circuit bikes)
5. Turn the key on and test both left and right signals. Confirm the flash rate is correct—if signals flash too fast or too slow, check your flasher relay.

Watch: The Turn Signal Circuit — Electrical Troubleshooting and Basics on a Vintage Honda Motorcycle

Frequently Asked Questions

Can I use LED bulbs in these turn signals?

Yes, but you will need to swap your stock thermal flasher relay for an Electronic Flasher Relay. The original Honda thermal relay relies on the higher current draw of incandescent bulbs to generate enough heat to cycle. LED bulbs draw much less current, causing the relay to flash too fast (hyper-flash) or not at all. The electronic relay uses a solid-state circuit that works with both LED and incandescent bulbs.

Do these fit the CB350F or CB400F?

These signals are designed for the Honda twin-cylinder and inline-four models listed in the fitment chart below. The CB350F (Four) and CB400F use a different turn signal mounting system and are not compatible.

My turn signals flash fast on one side but normal on the other. What is wrong?

A fast flash on one side almost always means a burned-out bulb on that same side. The flasher relay speeds up when it detects reduced current draw from a missing or dead bulb. Check both the front and rear signal on the fast-flashing side and replace any burned-out bulbs. If all four bulbs are good, check the ground connections at each signal.

Do I need to buy separate stems or mounting hardware?

These signals include the retaining nut and washer for mounting. They clamp onto the turn signal stems already on your bike. If your original stems are damaged or missing, you will need to source replacement stems separately.

What is the difference between these aluminum bullet signals and the other bullet signals you sell?

These aluminum bullet signals (SKU U3207) feature a single-piece aluminum body and a dual-filament 1157 bulb that supports both turn signal and running light functions. The standard Chrome Bullet Turn Signals and Black Bullet Turn Signals use a single-filament bulb wired for turn signals only. If your bike has a running light circuit (1974+), the aluminum version covers both functions without extra wiring.

You Might Also Need

• Turn Signal Flasher Relay — OEM-style thermal replacement
• Electronic Flasher Relay — required for LED bulb conversions
• Replacement Turn Signal & Tail Light Bulbs
• Headlight Bucket & H4 Bulb Kit — complete front headlight upgrade
• Headlight Brackets — chrome, black, or stainless steel
• Electrical Connector & Repair Kit — bullet connectors, spade terminals, heat shrink, wire

Last updated: March 2026