Mufflers | Honda CB360
Period correct mufflers that fit and work well on the Honda CB360. Stainless steel t-bolt clamps, universal mounting brackets, and full hardware kit included with each set of mufflers.
Why You Need This
Are your CB360's mufflers looking like Swiss cheese? Finding an original pair in good condition can be a challenge, so we offer these clean replacement mufflers. Though not exact reproductions of the Honda CB360 mufflers, they maintain a period-correct, stock-style appearance and fit very well. These mufflers are a cost-effective alternative to aftermarket systems and will optimize engine performance over open pipes. They produce a great sound, adding a bit more gusto to your motorcycle. Mufflers are sold in pairs.
Specifications
| Spec | Detail |
|---|
| Replaces OEM Parts | 18300-369-730, 18300-369-000, 18300-369-007, 18400-369-730, 18400-369-000, 18400-369-007, 18310-387-307, 18310-387-300, 18410-387-307, 18410-387-300 |
| Fits Models | CB360G (1974), CB360T (1975–1976) |
| Material | Chromed Steel |
| Sold As | Pair |
| Baffle | Removable mechanical baffle. Additional fiberglass packing can be added if desired. |
| Muffler Clamps | Stainless T-Bolt Clamps |
Note: Sold in Pairs - 1 pair is enough for 1 motorcycle
Note: Does not qualify for free shipping
Note: Graphite crush gaskets are sold separately but HIGHLY RECOMMENDED for a solid leak-free connection. They are a one-time-use part — order a fresh pair any time the mufflers come off.
What's in the Kit
- 1 x #5360 Left Muffler
- 1 x #5361 Right Muffler
- 2 x Stainless Steel T-Bolt Clamps
- 2 x Universal Chromed Steel Mounting Bracket
- 2 x Universal Muffler to Header Sizing Collars
- 2 x Mounting Hardware Kits
Installation
Difficulty: Intermediate
Tools needed: Metric hand tools, Allen wrench, Flathead screwdriver, File, Hacksaw, Step drill bit, Adjustable wrench
- Remove the old Honda CB360 mufflers and inspect the header pipes for wear or damage.
- Replace the copper exhaust gaskets at the cylinder head if the originals are badly flattened. Those are a different gasket from the graphite crush gaskets that seal the muffler to the header pipe.
- Clean the header pipe ends and install the graphite crush gaskets or included collars before fitting the mufflers. (See the full installation article for gasket recommendations.)
- Mount the mufflers using the factory brackets or modify the included universal brackets as shown in the full installation article.
- Use the included stainless T-bolt clamps over the muffler inlets for final assembly.
- Slide each muffler onto the header pipe until it seats correctly right before the stop ring. Ensure the muffler is not positioned over the stop ring.
- Leave all mounting hardware loose and align the complete exhaust system before final tightening.
- Adjust the mufflers for proper frame, foot peg, and center stand clearance. See the full installation article for alignment tips.
- Tighten the header, bracket, and clamp hardware evenly to create a secure, leak-free exhaust seal.
- Complete a final fitment check before riding. Refer to the full installation article for troubleshooting, service tips, and future exhaust removal recommendations.
These installation steps are shortened to get a quick idea of installing the mufflers on your CB360 motorcycle. Be sure to refer to our video below and full installation guide before installing them on your motorcycle.
Our muffler installation guide will walk you through installing your new Common Motor mufflers from start to finish on the CB360 twin cylinder motorcycle.
Frequently Asked Questions
Can I reuse the factory muffler mounting brackets on a Honda CB360?
Yes. The factory brackets are the preferred option. The brackets are left- and right-side specific and must be installed in the correct orientation.
Will the factory CB360 brackets require modification?
Possibly. We recommend test fitting each muffler with the factory bracket before install to see where the muffler sits. If your muffler does not sit at the correct spot, follow our factory bracket modification instructions in the installation video to mark your bracket and drill a new hole to accommodate the slight difference.
Do I really need the graphite crush gaskets?
The graphite gasket provides the superior seal and is the method the factory mufflers use between the mufflers and header pipe. We do not recommend the metal adapter collars when graphite crush gaskets are available.
Can I take the mufflers back off later for service?
Plan on new graphite gaskets if you do. The gasket is crushed as you tighten the clamp, so once it has taken a set it will not seal again. Do not pull a muffler off the header pipe unless you have a replacement gasket on hand.
Can I remove the baffles from these mufflers?
Yes. The mechanical baffles are removable and can be inspected, cleaned, or packed with additional baffling.
Should I use threadlocker on the muffler hardware?
Yes, we recommend using red threadlocker on the bracket bolts if desired, but only after the full exhaust system is mocked up and aligned.
Will this fit my CL360 or CJ360?
Yes and no. If you find a set of used original CB360 headers and collars, then they can be bolted onto your CL360 and CJ360 with these mufflers in the same manner.
You Might Also Need
Last updated: August 2026