COMMON MOTOR COLLECTIVE
Bullet Electrical Connector (Double Female)
Bullet Electrical Connector (Double Female)

Bullet Electrical Connector (Double Female)

Your Price: $8.00
In Stock
CMC Part Number:K3087
  • Qty:Sold in Sets

Optional Add-On Parts:
Open Barrel Crimp Tool (#9043) (+$40.00)
UP: Double Female Bullet Connectors
#3275 (x10)
UP: Female Double Bullet Connector Covers
#3088 (x10)

Double Female Bullet Connectors & Rubber Covers | Vintage Honda CT90 Through CB750

Replacement double female bullet terminals with rubber covers for the wiring harness on vintage Hondas. A double female lets two male bullets connect into a single wire, which is why they’re sometimes called two-into-one terminals. The originals are often loose, corroded or missing altogether. Made in Japan, in packs of 10 terminals with 10 rubber covers.

Why You Need This

These double female bullet terminals replace the often cracked or missing originals on your harness. For a single connection, we also carry single female bullet terminals. Ours are made in Japan and are better quality than the “mystery” bullets sold elsewhere.

Butt splices and tap-in clip connectors are temporary fixes. A crimped and soldered bullet with its rubber cover is a permanent repair that looks like it came from the factory.

Specifications

SpecDetail
TypeDouble Female bullet terminal with rubber cover
Mates WithTwo male bullet terminals, joined into a single wire
MaterialTin-plated brass
Made InJapan
Recommended Wire Size16 gauge
Fits ModelsCT90 (1966–1978), CB100 (1970–1975), CL100 (1970–1973), CB125S (1973–1978), CL125S (1973–1975), CB175 / CL175 (1968–1973), SL175 (1970–1972), CB200 (1973–1976), CL200 (1974), CB350 / CL350 (1968–1973), SL350 (1969–1973), CB350F (1972–1974), CB400F (1975–1977), CB360 (1974–1976), CL360 (1974–1975), CJ360 (1976–1977), CB450 (1965–1974), CL450 (1967–1974), CB500K (1971–1973), CB500T (1975–1976), CB550K (1974–1978), CB550F (1975–1977), CB750K (1969–1978), CB750F (1975–1978), CB750A (1976–1978)
Sold AsOne pack: 10 double female bullet terminals and 10 rubber covers

Note: Bullet sizes varied by model and year, even on factory harnesses. If a connection feels tight or loose, adjust the female side: open it slightly with a small screwdriver, or close it slightly with pliers. A male bullet can’t be resized. Replacing both halves gives a fresh, proper fit.

What’s in the Pack

  • Double Female bullet terminals (10)
  • Rubber covers (10)

Installation

Difficulty: Intermediate

Tools needed: Open-barrel crimp tool (yes, you will need it), wire stripper, and a soldering iron.

Chart comparing correct and incorrect open-barrel terminal crimps
Correct and incorrect open-barrel crimps. Tap or click it to open the full-size version.

  1. Slide the rubber cover onto the wire before you fit the terminal. A little window cleaner helps a tight cover slide on.
  2. Strip the insulation and test-fit the wire in the terminal. Trim the bare end until it seats properly in the barrel.
  3. Crimp the rear tabs around the insulation first, using the larger opening on the crimp tool.
  4. Flip the terminal and crimp the inner tabs around the bare wire.
  5. Give the inner crimp a second squeeze with the end of the crimp tool.
  6. Solder the connection for a permanent hold. Work quickly and use the tiniest drop, because the iron’s heat can melt the wire insulation.
  7. Slide the rubber cover up over the finished terminal.

Crimping takes practice. Keep some spare wire and terminals on hand for your first few.

Our wiring harness electrical connector video covers stripping, crimping and soldering bullet terminals like these.

Frequently Asked Questions

Will these fit the bullets already on my harness?

Bullet sizes varied by model and year, even on factory harnesses. If the fit is tight or loose, adjust the female side with a small screwdriver or pliers. Replacing both halves of the connection gives a fresh, proper fit.

Do I really need the crimp tool?

Yes. These are open-barrel terminals, and a proper crimp tool is what gets a solid crimp. Needle-nose pliers give mediocre results.

What size wire do these take?

The suggested wire size is 16 gauge.

My old bullet connector is corroded. Can I clean it?

The best fix is to cut it off and crimp on a new one, then add a dab of dielectric grease to the connection.

Two male bullets going into my double female don’t fit the same. What do I do?

That happens, because bullet sizes varied even on factory harnesses. Adjust the female to suit, or replace the mismatched connector with a fresh one.

How do I get two wires into one terminal?

Solder them. When two wires share a single terminal, we solder the connection rather than relying on the crimp alone.

You Might Also Need

Last updated: November 2026

These Double Female Bullet Electrical Connectors Work with These Honda Motorcycles
19651966196719681969197019711972197319741975197619771978
CT90CT90K0CT90K0CT90K0CT90K1CT90K2CT90K3CT90K4CT90K4CT90K5CT90K6CT90K7CT90K8CT90K9
100
125
CB100K0CB100K1CB100K2CB100K2CB100K2CB100K2
CL100K0CL100K1CL100K2CL100K3
CB125 S0CB125 S1CB125 S2CB125 SACB125 SACB125 SA
CL125 S0CL125 S1CL125 S1
175CB175K0CB175K3CB175K4CB175K5CB175K6CB175K7
CL175K0CL175K3CL175K4CL175K5CL175K6CL175K7
SL175K0SL175K1SL175K1
200CB200K0CB200K0CB200TCB200T
CL200
350CB350K0CB350K1CB350K2CB350K3CB350K4CB350K5
CL350K0CL350K1CL350K2CL350K3CL350K4CL350K5
SL350K0SL350K0SL350K1SL350K2SL350K2
360CB360GCB360TCB360T
CL360K0CL360K1CJ360TCJ360T
450
500T
CB450K0CB450K0CB450K0CB450K1CB450K2CB450K3CB450K4CB450K5CB450K6CB450K7CB500TCB500T
CL450K0CL450K1CL450K2CL450K3CL450K4CL450K5CL450K5CL450K6
350F
400F
CB350FCB350FCB350FCB400FCB400FCB400F
500K
550
CB500K0CB500K1CB500K2CB550K0CB550K1CB550KCB550KCB550K
CB550FCB550FCB550F
750CB750K0CB750K0/K1CB750K1CB750K2CB750K3CB750K4CB750K5CB750K6CB750K7CB750K8
CB750F0CB750F1CB750F2CB750F3
CB750ACB750ACB750A
5 Stars
Great replacement for fatigued and broken factory connectors
Thank you Common Motor for stocking these unique connectors! I had a bad one in the ignition coil circuit and this got me up and running at minimal cost and retaining the compatibility with all the stock wiring.
Did you find this helpful?  1 of 1 Found Helpful
Reviewed by: (Verified Buyer)  from OH. on 10/8/2024
5

Related Items

 

Recently Viewed Items

Logo