COMMON MOTOR COLLECTIVE
Petcock | Honda CL175 / CL200
Petcock | Honda CL175 / CL200

Petcock | Honda CL175 / CL200

Your Price: $40.00
In Stock
CMC Part Number:6007-175/200
  • Replaces OEM Part:16950-292-000, 16951-292-000, 16953-298-000, 16961-298-000, 16950-343-670, 90303-268-000
  • Qty:Sold Individually

UP: Petcock
6007
Optional Add-On Part:
3 ft. Polyurethane Fuel Line – 5.5 mm I.D. (#9034) (+$9.00)

Aftermarket Petcock | Honda CL175 / CL200

A petcock that leaks or won't let enough fuel through is a common problem on a vintage Honda like the CL175 or CL200. This aftermarket replacement is a replica of the original Keihin petcock, and it comes ready to install out of the box with new rubber seals and a filter screen.

Why You Need This

The original petcock on a 1970–1974 CL175 or CL200 is 50 years old or more. Its rubber seals dry out and let fuel seep from the tank. Its filter screen can clog, so fuel can't get through to the carburetors, or get damaged and let debris through to them.

This petcock is a complete assembly, so it bolts straight onto the tank with no parts to swap over from the old one. If your original OEM petcock is still in good shape and just needs new seals, we also sell the OEM petcock rebuild kit and a replacement OEM brass filter screen for it.

From the K4 on, the CL175 scrambler and the street CB175 use different petcocks, and the petcock has to match the tank it bolts to. This one fits CL175 K4–K7 and CL200 tanks. CB175, SL175 and CB200 tanks, and the early 1968–1969 CL175 K0 and K3, take our CB175 / CB200 petcock.

Specifications

SpecDetail
Replaces OEM Part Numbers16950-292-000, 16951-292-000, 16953-298-000, 16961-298-000, 16950-343-670, 90303-268-000
Fits ModelsCL175 K4–K7 (1970–1973), CL200 (1974)
Sold AsSold Individually
IncludesComplete petcock with new rubber seals and filter screen
DesignKeihin-style replica

Note: Skip inline fuel filters. With a clean tank, the petcock's built-in filter screen is all the filtration you need.

Note: A rebuild kit for this CMC aftermarket petcock is available if it needs new seals down the road. That kit fits only this aftermarket petcock, not the OEM Honda petcock, and the OEM rebuild kit doesn't fit this one.

Installation

Difficulty: Beginner

  1. Turn the old petcock off and disconnect the fuel lines from it.
  2. Drain the tank into a safe container, then remove the old petcock from the tank.
  3. Thread the large nut onto the new petcock, smooth side up, by only about half a turn. It's reverse-threaded on the petcock side.
  4. Hold the petcock in position and turn only the nut onto the tank. Both sides draw in evenly and squeeze the gasket in the middle of the nut. Tighten it snug, not overtight.
  5. Reconnect the fuel lines to both outlets. Keep both outlets facing the back at the same height, or the lower one takes all the fuel.
  6. Check for leaks, and check fuel flow at the on and reserve positions, before you start the engine.

Clean the tank before you fit the new petcock. Rust and varnish left in the tank can clog the new filter screen. If you clean the tank with vinegar, take the petcock off first, because the acid can damage it.

Our gas tank cleaning video walks through cleaning a rusty vintage Honda tank with household white vinegar, including taking the petcock off first.

Frequently Asked Questions

Will this fit my CB175, CB200 or early CL175?

Only if the bike has a CL175 K4–K7 or CL200 tank fitted. A CB175, SL175 or CB200 tank, or a 1968–1969 CL175 K0 or K3, takes our CB175 / CB200 petcock instead.

Why is fuel only coming out of one outlet?

It's rare to see fuel flow from both outlets at the same time. The outlets are connected. While the float bowls are empty, fuel takes the easiest route, and the flow evens out as the carbs fill. Test with a full tank, and make sure both outlets face the back at the same height, because the lower one can take all the fuel. If one carb never gets fuel, contact us.

Do I need an inline fuel filter with this petcock?

No. With a clean tank, the petcock's own filter screen provides all the filtration your carburetors need. An inline filter limits fuel flow and can cause running problems at higher RPM.

Can I rebuild this petcock if it starts leaking later?

Yes. Our rebuild kit for this CMC aftermarket petcock includes a lever gasket, sediment bowl O-ring and petcock-to-tank gasket. When you put it back together, don't pinch the wavy washer between the petcock body and the faceplate. The OEM rebuild kit won't fit this aftermarket petcock.

You Might Also Need

Last updated: October 2026

This Petcock Fits These Honda Motorcycles
19701971197219731974
175CL175K4CL175K5CL175K6CL175K7
200CL200

Related Items

 
 

Recently Viewed Items

Logo